• Operational mode
    The semi-automatic welding machine operates in three modes: MIG / MAG / FLUX, TIG DC-LIFT and MMA. In the MIG / MAG / FLUX mode, work is performed by feeding the welding wire automatically to the welding location. Manual arc welding with a consumable electrode (MMA) is great for working with large metal structures from ferrous metals. And if you need to work with high-alloy steel and its alloys, then this task is perfectly handled by an inverter in TIG DC-LIFT mode.
  • Control panel
    The semi-automatic welding machine is controlled from the front panel. There are two switches, three-mode and two-mode. With the three-mode switch you can select the welding mode MIG / MAG / FLUX, MMA or TIG DC-LIFT. A dual-mode switch makes it possible to switch the operating mode between feeding the wire from pulling the 2T trigger and continuously feeding the 4T wire. To increase comfort, two electronic displays are displayed on the front panel showing the installed voltage and current and also the knobs for adjusting them. Three LEDs indicate the operating status of the machine.
  • Bayonets
    The bayonets made of high-quality materials are used for reliable connection of welding cables. This type of connectors has been specifically designed to meet safety and reliability standards. The used format of bayonet ensures a tight connection of the contacts, reducing the resistance of the current being conducted, allowing the use of welding cables of increased length.
  • CEE plug
    This type of connection is considered to be optimal when working with semi-automatic welding. Connecting the burner to the CEE plug does not require additional fasteners, separate wiring of the hoses and control cable. A welding wire is fed through the connector, and the gas mixture is fed and the burner is controlled. All control components and the hose are in a common outer casing, thereby reducing the likelihood of mechanical damage.
  • Wire-feeder
    The task of the mechanism is to ensure continuous feeding of the electrode wire through a flexible hose to the welding zone. Constructively simple mechanism consists of an electric motor, a reducer and a system of feed and pinch rollers. The case of the electrode wire-feeder is made of metal and plastic. Presser rollers are used to pull the electrode wire from 0.6 to 1 mm.
  • Device settlement
    The welding machine is equipped with air cooling, consisting of a fan blower and a radiator system located in places where a high heat sink is required. The installed fan passes the right amount of air through the inverter, ensuring timely cooling of internal components. The inverter is equipped with an overheating protection to ensure reliable operation, which turns off the inverter automatically. The device can be switched on again after cooling to the required operating temperature. Components from world manufacturers are use, in power pulse technology to increase the working cycle. The power units of the welding machine are coated with a compound designed to protect and reduce the likelihood of electrical breakdown. The main board is covered with a layer of varnish, providing additional protection from external damage.
id: 00011
Tex.AC TA-00-023 semiautomatic welding set is designed to perform all kinds of welding on DC. High level of welding is provided by components from world manufacturers. The qualitative result during work with solid wire, as well as non-consumable tungsten electrode provides microprocessor control, which monitors the operation of all systems.

Characteristics
Мodel ТА-00-023
System nominal voltage (W) 180-240
Network frequency (Hz) 50
Power rating (kWn) 7,6
Class of case protection IP21S
Insulation class H
Dimensions L/H/W (mm) 280/195/440
Weight (kg) 11
Warranty (mon) 36
Equipment n/a
Mode MIG\MAG\FLUX
Current adjustment range (A) 30-190
Working cycle (%) 60
No-load voltage (W) 65
Wire feed speed adjustment range (m/min) 0,8-24
Gage of used one-piece wire (mm) 0,6-1,0
Mode ММА
Current adjustment range (A) 30-160
Used electrodes (mm) 1,6-4,0
Working cycle (%) 60
No-load voltage (W) 65
Mode Lift TIG
Current adjustment range (A) 20-190
Working cycle (%) 60
No-load voltage (W) 65
Diameter of used welding rod (mm) 1,2-3,2